CD4001 PDF

; Manufacturer: Major Brands; Manufacturer no.: CD Texas Instruments [ KB ]; Data Sheet (current) [ KB ]; National Semiconductor [ KB ]. The CDBC and CDBC quad gates are monolithic complementary MOS (CMOS) integrated circuits con- structed with N- and P-channel enhancement. The CD quad gate is a monolithic complementary MOS (CMOS) integrated circuit constructed with N- and P-channel enhancement mode transistors.

Author: Zulkikree Maubei
Country: Jordan
Language: English (Spanish)
Genre: Business
Published (Last): 23 October 2013
Pages: 357
PDF File Size: 15.93 Mb
ePub File Size: 4.45 Mb
ISBN: 477-8-82479-433-3
Downloads: 88769
Price: Free* [*Free Regsitration Required]
Uploader: Fezragore

Access Denied

But as capacitor charges cd4001 on resistor drops to half the power supply NI1 detects a high on in its input pin 2 as a result logic 0 appear on pin 3. Choosing Motor For Robots.

And if any the inputs are high we will receive the low output. Negative is connected to pin 7 and pin 14 is connected to power supply. Interface GPS with Arduino.

CD4001 – Quad 2-In NOR Gate

Interface SD Card with Arduino. As a result current start following in capacitor and capacitor starts to charge. Latest Blogs Web Browsers: It can deliver approx. In another words we will receive the high output when both the signals goes low.

In the diagram above consider that we have supply logic low to pin1 of NI1 as a result we will receive logic 1 in output pin 3 if you have assume pin 2 of NI1 be low. They are omnipresent in The circuit describe below can be used in many application like it can we use as fake light to create an impression that alarm has been fitted or you can use it in your vehicles when your car broke down as it will give eye catching appearance to the car passing near to your vehicle.

Related Posts (10)  MICROTRENDS MARK PENN DOWNLOAD

Generating time delay with IC. As a result pin 8 is also high and now again assume pin 9 to be low now we will receive 0 at output pin of NI3 and as a result output pin ofNI4 will receive high and LED start glowing.

Skip to main content. Group all Htabs Electronics. Atmospheric Vortex Engine Twister Power.

This means that we will receive 6V at pin 4. It consists of 4 independent NOR gate in a single chip. Now logic 0 is on pin 5 ad 6 we will receive logic 1 at pin 4 of NI2. Thus a particular value of resistor, for fixed voltage, limits the current through it.

From above we can see that for a certain period of time circuit will work and then goes off.

CD – Quad 2-In NOR Gate

Its resistance is given by the ratio of voltage applied across its terminals to the current passing through it. Choosing Battery for Robots. Each gate has 2 inputs and 1 output.

Resistor Resistor is a passive component used to control current in a circuit. As we can see in the truth table it will provide the output equal to one when both of the input is low. Working voltage range of IC is from 5V to 15V.

Related Posts (10)  ENCICLOPEDIA SALVAT DEL AUTOMOVIL PDF

As you can see in the circuit below. Now voltage on pin 8 is also low at this time and assume voltage on pin 9 to be low as a result we will receive high at pin 10 of NI3 which also make pin 12 and 13 of NI4 to high and we will receive low on pin 11 as you can see from truth table and LED connected to it will not glow.

In first gate NI1 pin 1 and 2 are for inputs and pin 3 is for output. SPI Module of Arduino. It has small notch on one side which is identified as pin 1. IC consists of 14 pin where pin numbers 7 and 14 are connected to battery or Cf4001 power supply.

Light sensor using photodiode. If we assume pin 9 of NI2 to be high then also we will get pin 0 to be high and low as you can now see from cd401 table.