Coefficient of Linear Thermal Expansion by TMA or Dilatometer ASTM E, ASTM D, ISO Scope: Linear Thermal Expansion is used to determine . This standard is issued under the fixed designation E; the 1 This test method is under the jurisdiction of ASTM Committee E37 on Thermal. ASTM E Linear Thermal Expansion of Solid Materials by Thermomechanical Analysis_机械/仪表_工程科技_专业资料。Designation: E
|Published (Last):||6 December 2011|
|PDF File Size:||9.10 Mb|
|ePub File Size:||7.40 Mb|
|Price:||Free* [*Free Regsitration Required]|
The specimen must be flat on both ends. Related information can be found in Refs. Standards can be obtained from appropriate standards authorities.
Coefficient of Linear Thermal Expansion ASTM E831, ASTM D696, ISO 11359
Related information can be found in Refs. Users of this test method are expressly advised that all such instruments e8331 techniques may not be equivalent. It is the responsibility of the user of this standard to establish appro- This test method is under the jurisdiction of ASTM Committee E37 on Thermal Measurements and is the direct responsibility of Subcommittee E It is the responsibility of the user to determine the necessary equivalency prior to use. The test method may be used at lower or negative expansion levels with decreased accuracy and precision see Section.
NOTE 4—Some materials, particularly composites, may require heat treatment to condition the specimen prior to test astk relieve stresses or distortions. NOTE 6—Normally, the expansion increases with the increase in temperature as shown in the schematic diagram of Fig. Current edition approved March 15, Certification Formally asfm that your products and services meet all trusted external and internal standards.
Place the specimen temperature sensor in contact with the specimen or as near to the specimen as possible.
Send us a request Need help or have a question? A graph is produced. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Coefficient of Linear Thermal Expansion ASTM E, ASTM D, ISO
This test method uses a smaller specimen and substantially different apparatus than Test Methods E and D Unless effects of moisture are to asym studied, use of dry purge gas is recommended and is essential for operation at subambient temperatures. The actual incremental force, mass, or stress above that required to make contact with zero force shall be noted in the report. E Terminology Relating to Thermophysical Properties.
This test can be used for design purposes and to determine if failure by thermal stress may occur. The observed expansion must be corrected for the difference in expansion between the specimen holder and probe obtained from atsm blank run in which no sample or a specimen of the material of construction of the probe is run. Send us a request Wilton UK: ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
No further reproductions authorized. The test method may be used at lower or negative expansion levels with decreased accuracy and precision see Section Formally confirming that your products and services meet all trusted external and internal standards.
Due to copyright restrictions, we are not able to provide copies of standards. Standard Test Method f Individual reprints single or multiple copies of this standard may be obtained by contacting Astk at the above address or at phonefaxor service astm.
Active view current version of standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. It is the responsibility of the user to determine the necessary equivalency aztm to use. Inspection Validating the specifications, value and safety of your raw materials, products and assets. Material Testing Coefficient of Expansion,? The temperature range may be extended depending upon the instrumentation and calibration materials used.
Originally approved in An abrupt change in slope of the expansion curve indicates a transition of the material from one state to another. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Alternatively, a dilatometer can be used. Such heat treatment must be included in the report. Global Reach Intertek is the industry leader with over 42, people in 1, locations in over countries.
Need help or have a question? Xstm the dilatometer, the test sample should be approximately The coefficient of linear thermal expansion can be calculated from these recorded data.
Other heating rates may be used but shall be noted in the report. NOTE 1—Users of this test method are expressly advised that all such instruments or techniques may not be equivalent. NOTE 3—It has been found with some materials that this level of?
Specimens that do not meet these requirements may result in increased imprecision. Assurance Enabling you to identify and mitigate the intrinsic risk in your operations, supply chains and business processes. Link to Active This link will always route to the current Active version of the standard.
Coefficient of Linear Thermal Expansion Video Learn more about linear thermal expansion in this video. Maximum imprecision in the calculated coefficient of linear thermal expansion may be estimated from the imprecisions in the individual measurements by the following wstm.
Enabling you to identify and mitigate the intrinsic risk in your operations, supply chains and business processes. Precision and Bias 6 Assurance Testing Inspection Certification. For the TMA, the test specimen should be between 2 and 10 mm.