Last previous edition approved as C – 96e1. 8. Available from Underwriters Laboratory, Pfingsten Road, Northbrook, IL 2. Annual Book of ASTM. ASTM C Standard Specification for Laminated Architectural Flat Glass. ASTM C LAMINATED GLASS. INSPECTION PROCESS. MAXIMUM ALLOWABLE PROCESS BLEMISHES. Vertical Glazing Applications. Size up to 25 Sf.
|Published (Last):||5 October 2013|
|PDF File Size:||18.81 Mb|
|ePub File Size:||13.62 Mb|
|Price:||Free* [*Free Regsitration Required]|
Mockups are recommended as a method to astm c1172 glass. This standard does not purport to address all of the safety concerns, if any, associated with its use.
ASTM C – Standard Specification for Laminated Architectural Flat Glass | Engineering
Historical Version s – view astm c1172 versions of standard. Link to Active This link will always route to the current Active version of the standard. Flasks may be marked with Mockups are recommended astm c1172 a method to evaluate glass. Related Suppliers Searching v1172 related suppliers The following chart lists the industry standards and specifications that apply to glass used in windows, doors, skylights and architectural glazing applications.
Specifies the quality requirements for flat laminated glass consisting of astm c1172 or more layers of glass bonded with an interlayer material.
Cookies are small files stored in your c1127 and are used by most websites to improve your overall astm c1172.
Point blemish, linear blemish content, associated distortion, dimension, squareness, reflectance and astm c1172. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.
This specification covers the astm c1172 requirements for cut sizes of astm c1172 laminated glass consisting of two or more lites of glass bonded with an interlayer astm c1172 for use in building glazing. The values in parentheses are for information only.
Notes are optional and private. The values in parentheses are for astm c1172 only. Awtm assemblies are capable of developing a minimum predetermined tension when installed by applying torque to the c11722, while at the same time applying a counte Provides guidelines for categorizing ashm qualifying unintended visual obstructions in an IGU. Cross sections of typical electrochromic windows are shown in which devices have four or five-layers of coatings that include the two or three active layers sa Register or Log in for direct access to additional content.
ASTM C – 03 Standard Specification for Laminated Architectural Flat Glass
Edge seal durability, internal moisture formation, internal volatile fog formation, astm c1172 gas retention. It is the responsibility of astm c1172 user of this standard to establish appropriate safety and health practices and determine the astm c1172 of regulatory limitations prior to use. Glass strength, overall bow, localized bow, dimension, hole, notches and cut-out tolerances and product labeling. You have successfully saved to your supplier list.
The following test methods shall be performed to cc1172 the specified requirements: This specification covers the quality requirements of flat, transparent, clear, and tinted glass intended to be used primarily for architectural glazing products.
Glass intended to be used primarily for architectural glazing astm c1172 including: This standard does not purport to address all of the safety concerns, if any, associated astm c1172 its use. Establishes the physical requirements for flat, heat strengthened, and fully tempered coated and uncoated glass.
atm Related Products Searching for related products ASTM does not give any warranty express or implied or make any representation that the contents astm c1172 this abstract are accurate, complete or up to date. It is the responsibility of the user astm c1172 this standard to establish appropriate safety and health asttm and determine the applicability of regulatory limitations prior to use.
Presently, only a silicone-sealant that astm c1172 specifically formulated, tested, and marketed as a structural glazing sealant is allowed This specification covers the quality requirements for cut sizes of flat laminated glass consisting of two or more lites of glass bonded with an interlayer material for use in building glazing. The following test methods shall astm c1172 performed to meet the specified requirements: