ASTM A860 EBOOK

ASTM A Specification for fittings used in high pressure gas and oil transmission and distribution system. This standard is issued under the fixed designation A/AM; the number 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel. ASTM A/AM Direct No.: + Fax No.: + Email: [email protected] Board No.: +

Author: Juzahn Nezahn
Country: Liberia
Language: English (Spanish)
Genre: Environment
Published (Last): 28 September 2014
Pages: 187
PDF File Size: 20.51 Mb
ePub File Size: 2.82 Mb
ISBN: 829-8-67177-280-4
Downloads: 53713
Price: Free* [*Free Regsitration Required]
Uploader: Dulmaran

What can I do for you? ASTM does not give any warranty express astm a860 implied or make any representation that the contents of this abstract are accurate, complete or up to date. Butt-welding fittings astm a860 from these. Within the text, the SI units are shown in brackets.

astm a860 Internal and external surface shall be examined when size astm a860 permits accessibility. A astm a860 analysis shall be performed on deposited weld metal for each heat of filler metal orfor submerged arc weldingeach heat of filler metal and batch of flux the weld metal shall be deposited in accordance with the qualified weld procedure. The product analysis shall be the basis for rejection.

Research use only,Commercial use is prohibited.

Link to Active This link will always route to the current Active version of the standard. One or more of the supplementary requirements may be specified in the order. Rectangular For Less than [7. In pallets, in plywood cases, in bulk. Fittings shall astm a860 be heat treat edby normalizingquenchingand.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. And over, Sizes tested Astm a860. The nickel content of the deposited weld metal shall not exceed 1.

The material for fittings shall be fully killed fine — grain material astm a860 by a. Combining values from the two systems may result in nonconformance with this specification.

JIS G Carbon steel pipes for ordinary piping. The chemical composition thus determined shall conform aetm Table 1. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Astm a860 G Steel pipes for low temperature service.

Within the text, the SI units are shown in brackets. JIS G Arc welded carbon steel pipes. Standard Specimen, Size Specimen. Starting materials shall consist of plate, sheet, forgings, ast, quality bar, and seamless or fusion-welded tubular products with filler metal added.

If astm a860 want to use it ,you can buy from following link: Work Item astm a860 – proposed revisions of this standard.

A chemical analysis shall be performed on deposited weld metal for. Section V, Nondestructive Examination. The values stated in each system are not exact equivalents; therefore, astm a860 system must be used independently a80 the other.

Materials shall be heat treated by normalizing, quenching, and tempering or stress relieving. And over, Astm a860 tested Section;min, specimen, thickness [7. JIS G Carbon steel pipes for pressure service. All butt — weld tees manufactured by cold —forming methods shall be liquid. Materials and Manufacture … Research use only,Commercial use is zstm. All fittings shall be furnished in the heat-treated condition. There sults shall conform to Table 1 for either.

It is astm a860 only and not an official part of the standard; the full text of the astm a860 itself must be referred to for its use and application. These fittings are for use in high — pressure gas and oil transmission and distribution system.

JIS G Carbon steel pipes for high temperature service. The nickel content of the deposited weld metal. This specification covers wrought high-strength low-alloy asym steel fittings astm a860 seamless and electric fusion-welded construction for applications in high-pressure gas and oil transmission and distribution systems.

ASTM A860 Grade WPHY 65 Buttweld Pipe Fittings

By Sea or By Land Packing: DIN Medium-weight threaded steel tubes. How can I help you? The chemical composition thus determined. After the removal of any cracksthe tees shall be re. These fittings are for use in high-pressure gas and oil transmission and distribution systems.

Specimens shall conform to required values astm a860 chemical composition and mechanical atsm, namely: This abstract is a brief summary of the referenced standard. JIS G Stainless steel pipes. Wrought austenitic and austenitic-ferritic astm a860 stainless astm a860 without specific inspection requirements BS EN Butt-welding pipe fittings Part 4: All values are Maximum unless A range is stated.