1. TOSHIBA Transistor Silicon NPN Epitaxial Type (PCT Process). 2SC Strobe Flash Applications. Medium-Power Amplifier Applications. 2SC datasheet, 2SC pdf, 2SC data sheet, datasheet, data sheet, pdf, TOSHIBA, TRANSISTOR SILICON NPN EPITAXIAL TYPE (PCT PROCESS) . Characteristics of the 2SC bipolar transistor. Type – n-p-n; Collector-Emitter Voltage: 30 V; Collector-Base Voltage: 30 V; Emitter-Base Voltage: 6 V.
|Published (Last):||2 December 2005|
|PDF File Size:||9.49 Mb|
|ePub File Size:||14.71 Mb|
|Price:||Free* [*Free Regsitration Required]|
Divide power out Vled times Ires by power in Vbat times Ibat and you’ll know.
Transistor 2SC2500, NPN, ТО-92
I used a small ferrite bead that was about 5mm in length, and maybe 4mm in outer diameter, 2wc2500 of F14 ferrite.
But who do I think I am, Peter from Arc? Polyester ; Capacitance Range: I used a 22ohm current limited resistor, which shows 0.
Looks like I’m going to have to desolder at least 1 LED and try and find measure current and voltage and all that. I think it is easier to find than Zetex part, especially in this region Asia-Pacific. Mouser Electronics har inaktiverat TLS 1. The 2N is supposed to be able to handle heaps of current as it is supposedly used in high frequency power amplification. The overall efficiency would be interesting to know. You know, I never even thought about measuring the output the way you mentioned. I’m going to try and fix that and see what happens.
Packing details Shipping Weight: The simulation doesn’t show whether this was the problem, but it is likely. Download 2n datasheet datasheet from ST Microelectronics.
Another point that drew me to them was that they are ratasheet for high speed switching. I did test it out on a simple satcure circut, but was disappointed with the output.
Is it possible to harness 2 transistors together? Yeah, so far, I’ve been investigating every single transistor available from my usualy source and none seem to fit the bill. Another Mod regulated SatCure circuit Daatasheet recently completed another mod. Adding a third winding to the transformer will modify this somewhat, but he basic problem remains the same.
2SC Datasheet –
I didn’t really dare to go higher than 6Vin, nor did I feel the need to since I was testing the circuit for future use in a 4AA mod. Another Mod regulated SatCure circuit Just wondering, many of the transistors with really low Vce sat also dtaasheet rather low Ic, which would not make them suitable if we 2wc2500 driving a large number of LEDs in parallel since the current delivered would need to be quite high.
Would it provide any improvements over a common A?
Guaranteed Delivery see all. That’s a scheme of 2sc25000 two transistors so their gains multiply which is good but Vsat is typically never under a volt or so which is bad. Contact the seller — opens in a new window or tab and request a postage method to your location.
2SC2500 Datasheet PDF
I found the same thing about no benefit of extra turns too. I’ll let you know what I come up with. Minimum Current Transfer Ratio: Does anybody know if either of these two mfrs.
YMMV as they say. Mr Al’s suggested Zetex parts datasheef be a better choice? If the item comes direct from a manufacturer, it may be delivered in non-retail packaging, such as a plain or unprinted box or plastic bag. I know the circuit suggests 2N or 2N mainly because he was looking at only 1 LED maybe a maximum of 3so the current draw isn’t very high.
The item is Cat No. Try stacking two with the same number of turns and see?
Try not to let them cross over. Flashlights and Parts WTS: I wound the core using 0. The voltage across the resistor lower LED voltage will give you the current by ohm’s law, the difference the voltage delivered to the load LEDs. Should that be high or low?
Image resizer by SevenSkins. With any boost circuit like this, one of the most important components is the transformer. They are both similar in that they are based on the SatCure circuit, but have added an extra transistor to regulate the output.
Will changing the core material, the wire thickness or the number of turns change the efficiency or output power? But I still must not be doing something right. Can you get them?